First of all, you need to prepare the materials and tools shown in the following figure: Bluetooth headset, Bluetooth headset charger, and plug bar. Then pick up the Bluetooth headset and find the charging hole of the Bluetooth headset, as shown in the picture. Next, you need to connect the charger to the Bluetooth headset. Finally, you need to plug the charger into the power strip again, so that you can charge the Bluetooth headset, as shown in the picture below.
Charging method of Bluetooth headset: Materials: Bluetooth headset, chargingApparatus and so on. Put the Bluetooth headset back in the headset compartment [red circle in the screenshot]. Plug the charging cable into the charging port of the headset bin [the red part in the screenshot]. When the charging indicator lights up red, it means that the charging is underway. When the charging is complete, the blue light will light up [the red part in the screenshot].
Charging Here is the following Bluetooth headset, the first time to use, generally can not find the power interface. Use the connector of the charging cable to plug it directly into the side hole of the Bluetooth headset, as shown below. The lid at the interface needs to be rotated to open. After plugging in the power supply, if it can charge normally, the earphone's power supply indicatesWhat if one of the Bluetooth headphones doesn't work?
How to do when the Bluetooth headset rings and does not ring Huawei When the headset of a Huawei mobile phone rings and does not ring, it may be that the current audio is set to mono output, and it is OK to reset it in the mobile phone. It may also be the connection error caused by no sound, at this time should delete the headset device in the Bluetooth on the phone, and then restart the pair.
Method When a ring does not ring, it may be caused by the lack of power of the headset, put the headset back into the battery box, and then wait for the full power to recover, and then enter the mobile phoneLine connection, and then both headphones will have sound.
The indicator light is on. Then you need to close the cover of the charging compartment of the Bluetooth headset and wait 1 minute. This may be because the left and right ears of the two headphones do not match successfully, resulting in only one headset connected when pairing with the phone. The specific solutions are as follows: 1. Solution: Reset the Bluetooth on both sides, follow the prompts, reconnect the two headsets, and then connect the mobile phone Bluetooth after success. Both headphones should be turned on at the same time when connecting the phone's Bluetooth.
1. NoneThe method of using the cable headset is as follows: When using the Bluetooth headset for the first time, you need to connect the Bluetooth of your mobile phone, take the Bluetooth headset out of the charging case, long press the on/off button on the back of the headset for two seconds, and the Bluetooth will automatically enter the normal pairing mode.
2, boot: First make sure that the left ear and right ear of the tws wireless headset are powered, if the power is insufficient, you can put it in the charging box first, when the power is enough, take out the two headphones, you can see that there will be a white button on the side of the headset, it is the startup key of the headset, and press and hold the button for 3S.
3, Apple wireless headset usage: playTurn on Bluetooth on your iPhone; Put the AirPods charging case next to the iPhone, and then the system will automatically pop up the setting animation; Click on the connection to complete the pairing. Tap the earphones twice to connect the call, and users can also go to Settings - Bluetooth, and then tap the AirPods icon to customize the earphones.
4, connect the mobile phone: turn on the Bluetooth headset. Turn on Bluetooth on your mobile phone to search for nearby Bluetooth devices. After searching for the Bluetooth headset, click Connect. When the connection is successful, the headset's power indicator will flash. Make and receive calls: answer and make calls,When the phone is connected, the Bluetooth earphone automatically connects and hears the call from the other party. To answer a call, press the power button of the headset. Press the power button when you hang up the phone.
5, how to use wireless headphones today I will introduce you to the use of wireless headphones 1 charging: First of all, ensure that the wireless headphones have sufficient power. Most wireless headphones come with a charging case, and you can charge them by placing them in the case. When the headphone battery is low, it can be put into the charging case for charging.
1, the first charge, you must use up the power in the headset and then charge, and not intermittent charge, must be full until. In other cases, you can wait until the Bluetooth headset is running out of power, or wait until the Bluetooth headset reminds you to charge. When the Bluetooth headset is about to run out of power, the Bluetooth headset indicator light will flash red every few seconds, and also accompanied by: dripping sound. At this point, you can charge the Bluetooth headset.
2, first put the headset back to the corresponding position of the charging case. Then close the charging case to charge. If the charging case is not charged, it is requiredConnect a usb port charger, connect to the power supply to charge. Check the charging indicator: Most Bluetooth headsets come with a charging indicator that shows the charging status.
3, when the factory Bluetooth headset battery is not fully charged. To fully activate the battery, charge the first three times for 6-8 hours. After each charge 2-3 hours can be. When charging, it is generally a red light, the headset is full of blue lights or green lights, and some of the lights are long after being fully charged. In order to achieve the longest battery life, it is necessary to master the correct method of charging the Bluetooth headset, that isCharge only when the battery is low.
4, the first step, put the Bluetooth headset into its special charging case. The charging box is not only a storage place for the headset, but also a base station for its charging. Most Bluetooth headsets are designed to automatically start charging by magnetic or contact after the headset is placed in the charging case. Make sure the earphones are properly placed in the charging case to avoid being unable to charge due to poor contact. The second step is to charge the battery by connecting the USB cable of the charging case to a power outlet or computer.
1, if your Bluetooth headset has one headset ringing and the other headset does not ring, you can try the following solution I told you: Check that the headset is correctly paired: Make sure that both headphones are correctly paired with the device. Sometimes, one headset may pair successfully with the device while the other does not. Try re-pairing the headphones, making sure both headphones are connected to the device. Check headset battery: Make sure both headphones are fully charged.
2, charging solution When a Bluetooth headset does not ring, it may be caused by the lack of power in the headset, whichWhen you need to plug in the earphone charging cable to charge, wait for the power to recover, and then connect to support wireless charging, you can put the earphone back to the earphone box to charge 2 reconnect as a Bluetooth earphone.
3. Reset If the headset of Huawei mobile phone rings one after another, it may be that the current audio output is mono. In this case, you can click the setting in the mobile phone, find the intelligent assistant page in it, and turn off the mono audio switch.
4, the method appears a ringing a ringing situation, it may be caused by the lack of power of the headset, put the headsetGo back to the battery box, then wait for the battery to recharge, then connect to the phone, and then both headphones will have sound.
5, when you encounter the Bluetooth headset one headset ring and the other does not ring, you can try the following methods to troubleshoot and solve: Confirm the connection problem: Check the Bluetooth connection: ensure that the Bluetooth headset has been successfully connected to the device, and the connection status is normal. Reconnect: Disconnect the Bluetooth connection and then reconnect the headset, sometimes reconnecting can solve the connection problem.