Do you want to ask the Mercedes car wireless charger fan has been turning how to do? Lower the temperature. The car wireless charger fan has been turning because the temperature is too high, and only a simple physical cooling is required. Mercedes-benz is a German automotive brand known for luxury and high performance, headquartered in Stuttgart, Germany, is a member of Daimler AG. Its products are all kinds of passenger cars, medium and large commercial vehicles.
The current sound at the wireless charging place may be generated by the fan under the charging place, as long as the temperature exceeds 30 degrees, the fan will run. This sound is related to the temperature inside the carThe degree is not related, but is affected by the temperature of other components near the bottom exhaust pipe. When the temperature rises, the fan starts.
First, find and remove hidden screws, the Mercedes-Benz c car radio charger device will be covered under the panel or other easily overlooked locations, need to find and remove any fastening devices, such as turnbuckles and clasps. Appropriate tools are required to assist in removal. Second, remove the panel and control module so that the charger body can be easily accessed. Avoid damaging any surrounding parts.
The current of this interface is only 5V/0.5A if the current voltage is notIf it does, the phone will be damaged. Some of the more high-end, relatively new cars are specially equipped with USB ports for mobile devices such as mobile phones. Most of these interfaces are located under the armrests and rear outlet, with current recognition, and can be used to charge the phone. Many people like to use a car charger, but please note that the output current of the car charger can not be less than the maximum rated input power of the phone.
1, this situation is not normal, the general mobile power supply is not sentMaking a noise. The reasons for this situation may be: 1, there may be water vapor on the mobile power motherboard, resulting in a slight short-circuit sound on the motherboard. 2, the mobile power motherboard in the process of boosting the sound, but the sound is usually very small, almost inaudible.
2, personal think and charging equipment, millet 80W wireless charging base built-in cooling fan, charging default open speed wireless charging mode (feel the noise can be manually closed), we can hear the fan in the process of charging "buzz" sound, hand close to the bottom of the wireless charging base, can also feelThe [Settings]. Next, under the Settings menu, find and click on [Battery]. Finally, open the switch button on the right side of [wireless reverse charging]. Huawei radio charging only for some mobile phones have this function, not all mobile phones have. Huawei Wireless charging method: Connect the charging head to the charging base using a data cable, and then plug the charging head into the power supply.
3, Enter My device First, in the mobile phone service My page, click and select to enter "My device". Click to view device parameters Click to select View Device parameters and proceed to the next step. Select fast charge for your phoneSelect the "Fast Charge" option to check whether the current phone supports wireless charging. Wireless charging Finally, after confirming, put the phone on the wireless charger, the charging prompt will be displayed, and it is OK.
4, if you are wireless charging, because there will be energy loss in the wireless transmission process, and then produce a certain amount of heat, there will be a phenomenon of wireless charging heat, this is normal.
Setting method: Set battery wireless charging SettingsCharging Silent mode/Silent while sleeping/Self-mute time/Always on ". Tips: ① At present, the models that support wireless charging are Ace 2, Find X3 series, OPPO Find N, etc. Wireless charging function is related to hardware, you can check whether the mobile phone supports the function by the above operation method. ② Silent mode for wireless charging only supports OPPO wireless charger.
After the silent mode is turned on, the fan runs at a low speed, and the wireless charger enters the low power operation state, and the maximum charging power is 12W. Automatic switching: Automatic switching to silent mode at night,The default start time is 00:00 to 6:00. At the same time, you can adjust the silence time independently according to your mobile phone usage habits. The self-adjustment function requires at least 10 days of mobile phone use cycle.
Tap your phone's desktop Settings. Open your phone's Settings and tap Battery. On the battery page, tap Wireless charging Settings. The Settings screen is displayed, and the function is always enabled. Charge your phone by placing it on a wireless charger.
The first step is to open the "Settings" window, and then click the "Battery" option as shown in the image below. Step 2 Enter the [battery] page, according to the followingAs shown in the figure, slide the circle after the "Wireless reverse charging" option to the right to enable this function. Finally, first click the "wireless charging Settings" option, and then set the relevant functions according to the requirements as shown in the figure below.
OPPO mobile phone models that support wireless charging include FindXFindX Pro, FindXFindX3Pro, FindX3Neo, FindX2Pro, Reno6Pro , RenoReno8Pro, FindXFindX5Pro, X202AceFindN, etc. Want to know how to do it in OSet wireless charging on the PPO mobile phone, you can find the battery option through the phone's setting menu, enter the wireless charging Settings, and turn on the always on function.
Make sure your OPPO phone model supports wireless charging. You can find this information in the phone's manual or Settings menu. Place the phone in the center of the wireless charger. The logo of the wireless charger may have a special pattern or color to ensure that you have placed the phone correctly. Plug the phone charger into the power supply and ensure that the voltage from the power outlet is sufficient to charge the phone. Enable the wireless charging function.