The charger does not support fast charging, the original charger 5V1A or 2V1A, 5W charger of course can not be fast charging. Or the fast charge protocol is incompatible and cannot be charged fast. 2 The charger is bad, even if it is the original charger, there is still a bad charger, it can not. 3 The charging cable, or the plug socket is not in good contact, resulting in a reduction in the input voltage, which is considered fault protection and does not start the fast charge.
This does not need to have a flash charge sign, you only need to see the electricity, run fastFast, generally speaking, it only takes about an hour, it can be full, if your half an hour, only about 10%, then it is not a flash charge. These are the signs about why there is no flash charge for my real phone.
Power, charging speed and color corresponding. If the battery capacity is greater than 10%, orange is displayed when the battery capacity is less than 90%. Blue is for fast charging. realme is a tech fad for young people. Adhere to the "dare to leapfrog" brand concept, to provide young users around the world with both leapfrog performance and fashion design of high-quality mobile phones and AIoT products.
Cause analysis: The battery is damaged. The system is faulty. Charger cause or poor contact. Solution: Try another charger, or data cable, or clean the charging port. Boot into the recover mode, select advancsd advanced mode, select wipeBattery, and clear battery traces. Restore factory Settings to check whether the system is faulty.
A. 20% is only virtual electricity, usually due to insufficient battery life caused by wrong operation, users often operate the mobile phone in the charging state, use non-original data cable to charge, charge for a long time when the power is empty, often makeCharge it with a power bank. According to the above reasons, the user is excluded one by one and solved one by one, and the above situation must not occur again, causing fatal damage to the battery.
Hello, this is a normal phenomenon, because the current is very small when it is close to saturation. It may be that the loss is equal to the output. Does not affect the use, if it affects your use, you can apply for after-sales service in the order.
No battery or poor contact between the battery and the charger causes the indicator to turn orange, generally only need to re-put the battery correctly to solve the problem. If it still shows orange, there may be a problem with the charger or data cable.You can change the charger or change the data cable to reconnect the charge to try. If it still cannot be solved, it may be a battery failure or aging, resulting in abnormal charging, you can change a battery to try.
Shutdown charging test. Replace the charging position and eliminate the intermittently slow charging caused by poor socket contact. If conditions permit, replace the standby charger for testing. Or send the repair test to boot charging, such as the mobile phone is equipped with a third-party plug-in such as charging doctor, it is recommended to uninstall the test.
Hello! This may be the battery into hibernation, it is recommended that you do not run out of power automatically shut down, please unloadRemove the battery for 5 minutes, then use the data cable to connect the computer and mobile phone for 30 minutes, and try to start again.
1, green: support QC charging. Blue: indicates USB0. If you strictly follow the description of the interface color in Wikipedia to distinguish, it is clear that green represents Qualcomm QC, purple represents Huawei fast charge, and the interface of other colors is not clearly defined. The color of the wire is only for the appearance level, and it does not help the material of the product.
2,Black/white: belongs to the USB0/0 era, is the most traditional speed, theoretically slow, only about 60MB/s, charging speed is also very slow. Dark blue: Belonging to the USB0 era, the theoretical maximum speed is 640MB/s, which is much faster than the previous generation. Light blue: belongs to the USB1 era, the theoretical maximum transfer speed is 1280MB/s.
3, the color of the USB data cable interface usually corresponds to different functions or standards. Specifically, black and white interfaces often represent the USB 0/0 standard, which supports lower data transfersSpeed and charging speed. The dark blue port represents USB 0, which provides a higher data transfer rate. The light blue port is further upgraded to represent USB 1, which is faster.