Operation method: Open the wireless microphone and the power supply of the receiving host, the wireless microphone generally has an automatic scanning function, which can scan the channel and frequency of the receiving host, and then it will automatically matchright. Do not use two wireless microphones at the same time. It is best not to use two wireless microphones together, which may cause signal interference and affect the normal use of the equipment. The microphone should not be too close to the mouth, which may affect the sound quality.
Wireless microphone is a kind of light, portable audio equipment, suitable for stage, podium and other occasions. This article will show you how to set up and use a wireless microphone to make your performance even better. Power on, one-click pairing Before using the wireless microphone, power on the wireless microphone and the receiving host. Wireless microphones usually have an automatic scanning function, which can be quickly foundTo receive the host's channel and frequency, one click complete pairing, so you can easily start the performance.
In order to make the best effect of the wireless microphone, it is necessary to deal with the relationship between the transmitter output level gain, the receiver output gain and the mixer input gain, such as improper handling may cause sound suppression, no penetration or sound distortion, and even excessive.
Wireless microphone has a transmitting end and a receiving end. Turn the receiving end of the wire into a 5-gauge small head, and then plug into the microphone input port of the computer. If the sound is too low, you can add a power amplifier between the receiver and the computer. Pick upIf the wireless microphone interface is 5mm, and the computer sound card input port is 5mm, you can use a wire with a 5mm plug at one end and a 5mm plug at the other end to connect.
Insert the receiver wire into the output hole on the receiver, just as the microphone is plugged into the air. Put the other end into the amplifier microphone audio port, the audio port will generally have a note here need to pay attention to check. Plug the power cord into the wireless receiver. Plug the other end in. Install the microphone battery, pay attention to the positive and negative terminals, the small end to the large end. Finally turn on the receiver power, and then turn on noneCoil power supply.
First connect the wireless receiver and audio; Then turn on the microphone and check the frequency band that the microphone is currently in; Use the button on the receiver to adjust the frequency band, and the two frequency bands can be linked to the microphone.
First connect the microphone receiver to the power supply and access the mixer input. Put the battery on the microphone, turn on the switch, and the indicator on the microphone shows green. Press the small rectangular button in the middle of the receiver to count on the displayThe word changes to another number. Unscrew the back cover of the microphone battery, there is an infrared port at the bottom, and align it with the small red dot to the left of the round key on the receiver.
Turn on the wireless microphone receiver controller and plug the wireless microphone receiver into the microphone port of the receiver controller. On the display of the receiving controller, make sure that the display is connected or matched. On the receiving controller's display, press the Mode button to select Pairing mode.
Insert Insert the receiver wire into the output hole on the receiver, the same as the microphone into the air. Plug the power cord into the wireless receiver. Plug the other end in. Battery installationThe microphone battery is installed, pay attention to the positive and negative terminals, the small end to the large end. Signal power on receiver. Power on wireless canister. The signal light will be green.
First, make sure the wireless microphone and receiver are fully charged and have enough power. Connect the wireless microphone receiver to the audio input interface of the speaker. This is usually done with a 5mm audio cable or RCA cable. If your stereo has a dedicated wireless microphone input interface, then you can connect to this interface directly using a wireless microphone receiver.
Which hole does Shivo wireless microphone plug in? Sivo whiteboard matching microphone has two jacks, the above 5 circular jack is for the outside of the microphone, you can plug a capacitor microphone, the following tail plug is a charging jack.
There is a USB data cable interface on the side of the wireless microphone, and you can charge it with the data cable connected to the charger. Among the random accessories, there are two charging data cables, one is the host, and the other is the microphone.
Charging port of K-song microphone K-Song microphone is divided into battery type and chargeElectric, first determine whether it is battery type or rechargeable, rechargeable microphone has a charging interface, can be charged directly into. Take a look at the bottom jack of the Phonping ph-120 phone K Gome. Insert the monitor earphone into the port marked with the earphone pattern.
First of all, put the battery of the wireless microphone into the microphone to ensure that the wireless microphone has sufficient electricity to use, and ensure that the audio output interface of the receiving box and the audio input interface of the sound are powered by the audio cableConnect and connect the receiver box power supply.
Wireless microphone is a kind of light, portable audio equipment, suitable for stage, podium and other occasions. This article will show you how to set up and use a wireless microphone to make your performance even better. Power on, one-click pairing Before using the wireless microphone, power on the wireless microphone and the receiving host. Wireless microphones usually have an automatic scanning function, which can quickly find the channel and frequency of the receiving host, and complete the pair with one click, so that you can easily start the performance.
Avoid microphone facing the speaker Generally singing with wireless microphones are directionalTherefore, the microphone stands on both sides of the speaker or behind the position, more will not produce buzzing feedback. If you need to stand in front of the speaker, be careful that the microphone is not directly facing the speaker. The heart-oriented microphone front is 180 degrees parallel to the speaker, or the super-directional microphone front is 120 to 140 degrees with the speaker.
Insert the receiver wire into the output hole on the receiver, just as the microphone is plugged into the air. Put the other end into the amplifier microphone audio port, the audio port will generally have a note here need to pay attention to check. Plug the power cord into the wireless receiver. Other end insertPower on. Install the microphone battery, pay attention to the positive and negative terminals, the small end to the large end. Finally, power on the receiver, and then power on the wireless canister.
Operation method: Open the wireless microphone and the power supply of the receiving host, the wireless microphone generally has an automatic scanning function, which can scan the channel and frequency of the receiving host, and then it will automatically pair. Device use note: it is best not to use the two wireless microphones together, there may be signal interference, affecting the normal use of the equipment. First of all, connect the microphone receiver to the power supply and access the mixer input.