1. Connection mode. You need three network cables. Connect to the router's WAN port, and then connect any two network cables from the router's four LAN ports to your desktop and laptop. Enter router Settings. So is setting IP to automatically get DNS on your desktop computer.
2, support virtual wireless router function, so you can use one computer broadband Internet access, and then use as a router, the other wireless Internet access.
3, wired connection desktop: Use a network cable to connect the desktop network card interface with the wireless router's LAN port.In this way, the desktop computer can be connected to the LAN by wired means. Wirelessly connected Laptop: The laptop searches for and connects to the Wi-Fi network of the wireless router. Typically, the router's Wi-Fi name and password will be labeled on the back of the router or on the instruction manual.
1. Solution for loose WAN port cable: Reconnect the network cable of the wireless router WAN port. Superior network deviceSolution: Reset or replace the upper-layer network device. Solution: Check whether the password of the dial-up account is correct. If no, change it. Network communication line problem solution: Consult the network provider, remote monitoring whether the line is normal. Broadband account expired or overdue.
2, before connecting the route, the switch directly out of the network cable to the computer, is required to dial again? Or directly assigned dynamic, static IP address? Write it down. If it is the latter, pay attention to the gateway IP address, be certain to distinguish, if it is the same as the default gateway of Mercury route, first modify the Mercury routeTake the gateway, route Mercury to the switch.
3, right click [Network] → Properties [Change adapter Settings] → [Local connection] → Right click local Connection properties] → [Double click TPC/IP protocol] → [Then click "Automatically obtain ip address"], [then click "Automatically obtain DNS" server address] → [Click OK]. Method 2: The Internet access configuration of the router is incorrect.
4, Hello! You can reset it and reset it. To set the Mercury router, proceed as follows: Enter the router address, connect the wireless router, and enter the address in the browserThe address you see on the router is usually 19161. Enter the corresponding account password, you will see to enter the corresponding account and password, generally the new purchase is admin.
5, said more general, can not connect to the network for many reasons, incorrect wiring, incorrect password account, WAN LAN port Settings are incorrect, MAC address cloning, address conflict will appear such problems, as well as hardware quality.
1, evenState IP address, click Save.
3, open the router base to find the management background or other similar files, and then remember the address of the router, here is not 1 but 31, so different router addresses are different. Then plug the router adapter into the socket and wait for the light on the router. Pull down the notification bar of your phone, find WLAN and long press it to enter the WiFi list.
RouterIn the Internet access mode (some routers called: networking mode, connection type, WAN port connection type, etc.), if the setting is wrong, it will cause the router networking failure, that is, it can not be used normally after connecting to wifi. In some areas, broadband operators will restrict users from using routers to access the Internet by binding the user's computer MAC address. In this case, the router cannot be connected to the network after normal Settings.
First check the line connection to see if it is caused by a hard fault. If the hardware is normal, power off the router, wait 5 minutes, and restart. In caseThe kind that automatically gets the IP, makes the computer reidentify it. In the meantime, set everything that needs to be set.
Check whether the broadband account is normal. Then replace another phone or set up a connection test to rule out problems that are not network. Restart the router or restore the router to factory Settings, re-dial the Internet, and reset the WIFI according to the setup wizard, or replace the router to dial up the Internet connection. If the WiFi name contains Chinese, you are advised to change it to English or a combination of English and numbers before connecting.
The trunk must be successfully bridged. After the bridge succeeds, set the secondary router toStatic IP can access the Internet, if there is no static IP set is unable to access the Internet, wireless router relay Settings, no relay signal after setting, even if there is no Internet access cause: DNS setting error. The secondary router uses the DNS of the primary router.
Because sometimes the system is connected, but can not get on the network state, this is because of the wrong password, the solution is relatively simple, and then enter the password again, it is best in the Wifi setting, first disconnect the network connection, forget the password, and then reconnect.
1, in general, it is possible to bring a charging bank on the plane, but the charging bank must meet the regulations before it can be carried on. A charging bank with a fixed energy of 100Wh can be carried on the plane, that is, a charging bank within 20000mAh can be carried on the plane. When the rated energy of the charging bank is greater than 100Wh and less than or equal to 160Wh, it must be reported to the airline and can be carried on the plane after approval.
2. You can carry the charging bank on the plane. About flying with a charging bank