1, directly disassemble the machine to replace the battery, can make the Apple phone charge, forEmergency.
2, the use of direct power charging mobile phone no power automatic shutdown can not open the machine, this time do not worry, the phone is not bad just because the power has run away so can not open. At this time, the standby power will be fine. Xiao Bian recommends using direct power to charge, rather than using a computer jack and mobile power, the latter two charging speed is very slow.
3, the iphone is out of power, use the charger to charge the iphone. The details are as follows: First connect the data cable to the mobile phone, and then plug it into the plug bar. Don't play games or watch videos while charging. Lithium battery workerThe suitable temperature is generally about 20℃, playing games and watching videos will make the phone battery temperature rise, and being in a high temperature state when charging will shorten the battery life. The charging time should not be too long.
4, you can turn off the power of the iPhone, and others will prompt to shut down when they call. You can also set Do not disturb mode or Offline mode by following these steps: Turn on Settings on your iPhone. On the Settings screen of your iPhone, select Do not Disturb Mode. Click on "Do not Disturb Mode". Note: During this process, unless it is a permitted call, others will not be able to call, and you will not have a ringtone orThe appearance of the Flextronics charger is similar to that of the original Apple charger, but the shell color is slightly different. The original charger shell is white, while the Flextronics charger shell is light yellow. In addition, there is no Apple logo on the Flextronics charger, but the internal chip and circuit board layout is the same as the original charger.
Yes. Apple's 20W charging head brand shows that it is manufactured by Flextronics, which is definitely the original Apple charging head product.
w fast charge has two foundries, one is Dongguan Flextronics, one is Selcon, these two are the foundries of Apple's past chargers. whicheverThe end of the original three lines must be neatly corresponding. A lot of imitation can be observed at the end of the uneven. The pin of the original charger is polished more round, bright and colored, and the imitation looks at the pin will be very dun.
is not genuine, it is produced by a small factory. Mobile phone chargers can be roughly divided into travel chargers, seat chargers and maintenance chargers, and the average user is mainly exposed to the first two. The biggest seller on the market is the travel charger. A good functional quality charger can identify lithium batteries and nickel-metal hydride batteries, and then determine the charging mode.
Not necessarily. Identify Apple 20W chargingThe method of head authenticity is as follows: the front of each 20W head will indicate the foundry information, as well as the 17-digit serial number, in fact, the serial number is as regular as the person's ID card code. At present, the 20W head is manufactured by Flextronics, Sercon and Flextronics India.
1, the charger is broken, repair or replace the new charger. The charging data cable is broken, replace the original data cable. Mains outage, wait for mains normal before charging. Charging of mobile phoneElectrical interface is broken, repair or replace the charging interface. The power management circuit of the mobile phone is faulty. Repair the mobile phone. The battery is broken. It can't be charged. Replace it with a new one.
2, most of this situation is because the mobile phone fell on the ground led to the motherboard components out of welding, the probability is very small. If the battery is not charged and the motherboard is damaged, the store will charge you more than 500 so-called replacement motherboard fees, in fact, only need more than 100 replacement power IC is good. Non-original charger, charging cable damage this easy to do, ask people for an original iPhone charger and charging cable to try to know.
3. If you are using a USB power adapter, make sure it is fully plugged in and the power outlet is working properly. If normal, there may be a problem with the power adapter, replace the power adapter to try. In general, the theory is that the battery will not be damaged with a charging treasure, as long as the voltage is the same, the current is at least faster, but it is still recommended to use a standard charger to charge.
4, the reason why the car charger can not charge the phone: the voltage is unstable when charging the phone will generally open the charging monitoring and detection program, if the program detects that the car charging voltage is notSteady, it stops the flush.
5, may be the mobile phone system failure caused by battery display problems. This problem is the easiest to solve, you can directly shut down and restart, which is equivalent to data refresh, and the general power display will be restored. The charger is faulty. This failure is the main reason why mobile phones cannot be charged. So how to judge the charger is good or bad. It's very simple. Try another charger.
New ipad for the first timeWhen the ipad indicates that the battery level is 10%, turn the new ipad off and connect it to the charger for charging. When using the ipad for the first time, although most of the power should be used up, but remember not to use up all the power.
ipad needs to pay attention to the following matters for the first charge: It is recommended that the new machine should not be in a hurry to charge, and the normal use of power will be charged when the screen prompts 10%. It takes about four hours to fully charge. This is only the approximate time, and the time will vary depending on the ambient temperature of the charging environment.
AppleFlat can be full, depending on the remaining power, usually about 2 to 4 hours, the current mobile device lithium battery does not have the so-called first charge, only the early nickel-cadmium battery has, lithium battery has no memory effect, can be charged with tax, flat charging, it is best to charge at less than 20% of the time, too low power is harmful to the battery, long time without use, It needs to be filled every 3 months to ensure that the battery lasts longer.
The best way to charge apple is to charge often, and start rushing when the power is less than 20%, rushing to more than 80% to 90%; The iPad has optimized the battery. It's fullIt doesn't matter if you don't unplug the power, the iPad will automatically power off, full immediately unplug the power is better for the battery; The first general charge 4 to 5 hours can be full, immediately unplug the power.
First plug the data cable into the air charging port, and then plug the two-hole plug into the socket. The time to use the remaining 10% for the first time and then fully charge it is about 4 hours.