Check the charging cable and charging port When you find that the Bluetooth headset cannot be charged, you first need to check whether the charging cable and charging port are normal. Sometimes, the charging cable may be damaged due to long-term use or improper storage, resulting in normal charging. At this time, you can replace a new charging cable and ensure that the charging interface is clean and dust-free to ensure smooth charging.
Bluetooth connection failure: Bluetooth connection failure is a common problem that can cause one or both headphones to run out of power. solutionBy disconnecting and repairing. Low battery on your device: If your device is low on battery, it will take longer to fully charge even if you put the AirPods in the charging case, causing one of the charging cases to not work. The solution is to charge the device to its full capacity.
If one headset is able to charge properly and the other is not, it is likely that the damaged headset battery has reached the end of its useful life. At this point, you can try to reset the headset or update the firmware to see if you can fix the problem. If these methods do not work, you may need to replace the battery or the entire eard='miair2se real wireless headphones open the cover after a flash in the right ear is finished, the left ear is not reversed '>miair2se real wireless headphones open the cover after a flash in the right ear is finished, the left ear is not reversed
According to your description, the following reasons are causing problems with your miair2se true wireless headphones: The electrical power in the right ear is low and needs to be charged: You can put the right earphone back in the charging case and wait for the earphone to be recharged. During the charging process, ensure that the charging case is fully charged. Abnormal earphone connection: Disconnect the earphone from your phone or other device, and then reconnect it. Mi air2se connected to the right ear no sound first put the left and right earphones into the charging case, while long press the left and right earphone touch parts for 7 seconds, the white indicator light of the earphone long, release the button. Earphone reset, old connection record is cleared, earphone white light flashes, goEnter pairing mode. Put the earphone into the charging case, press and hold the touch part of either earphone for 3 seconds and release it. The white indicator light of the earphone blinks (either earphone blinks), and the earphone waits for connection. Enable Bluetooth, search for and connect Mi Air2 SE. For the connection password, enter 0000. (After pairing successfully or no pairing connection times out, the indicator goes off. Bluetooth headset or headset case does not charge, oneGenerally due to non-compliance of charging head, data cable, charging port or earphone shrapnel caused by dirt, you can try the following methods: Replace the charger (data cable) charging, determine whether it is the charger (data cable) problem, it is recommended to use the original data cable, and replace the regular brand charging head try. There are generally two possible reasons for the Bluetooth headset not being charged. The first type of Bluetooth headset internal failure, such as battery or circuit damage, charging interface short circuit, etc. If it is for the above reasons, the headphones need to be sent for repair. The second charger or data cable has a problem, resulting in charging cannot continue. Replace the matching charger or data cable to recharge. If the real wireless Bluetooth headset can not wireless charging, you can try the following investigation: It is recommended that you use a regular brand wireless charger that meets the QI standard protocol. When using a mobile phone or tablet to wireless reverse charge the Bluetooth headset charging case, ensure that the mobile phone or tablet wireless reverse charge switch is turned on. During wireless charging, place the charging box correctly and ensure that the center of the wireless charging coil and the wireless charger coil of the charging box are aligned. Please observe the earphone charging contact and charging box charging shrapnel or probe is stained with oil/sweat or dirty, if yes, try to useClean up with a dust-free cloth or cotton swab. Tip: The charging contact is the only channel for the communication between the charging box and the headset. If the charging contact is poor due to dirt and other reasons, the headset will not be charged in the box, and the headset will be connected continuously with the cover closed. When it is found that the Bluetooth headset cannot be charged, it is first necessary to check whether the charging cable and charging interface are normal. Sometimes, the charging cable may be damaged due to long-term use or improper storage, resulting in normal charging. At this time, you can replace a new charging cable and ensure that the charging interface is clean and dust-free to ensure smooth charging. 1. It is recommended that you clean the charging port and try charging again in a suitable environment at room temperature. 2, the headset has not been used for a long time, it is recommended that you charge for a period of time to activate the headset. The charging box is out of power (the indicator light is red or not after opening the cover), it is recommended that you charge the charging box first. The charging environment temperature of the headset is not 2 to 40°C (low temperature will reduce battery activity), it is recommended that you charge the headset at normal room temperature. 3. Observe the earphone charging contact, charging box charging shrapnel or probe is stained with oil or dirty, if there is a clean cloth or cotton swab dipped in medical alcohol to wipe (OPPO Enco X Bluetooth headset do not clean by yourself). Click to view "True wireless Bluetooth headset cleaning and maintenance tips" If the above methods can not solve your problem, it is recommended that you bring the headset and purchase voucher, go to the nearest OPPO customer service center, by professional engineers to detect and deal with. 4, if the real wireless Bluetooth headset can not wireless charging, you can try the following investigation: It is recommended that you use a regular brand wireless charger that meets the QI standard protocol. Use your phone or tabletWhen charging the Bluetooth headphone charging case, ensure that the mobile phone or tablet wireless backcharging switch is turned on. During wireless charging, place the charging box correctly and ensure that the center of the wireless charging coil and the wireless charger coil of the charging box are aligned. 5, the two headphones are not connected, you cancel the Bluetooth headset that has been paired in the mobile phone, and then put the headset into the charging bin, and then take it out again, and then the two ears will automatically connect, and then the mobile phone will search for the device again. If that doesn't work, bring the headphones back to factory and try again. 6, not connected, many Bluetooth headphones sometimes appear can not connectThe phenomenon of connection. It is shown that the headset enters the version of the code state, but the mobile phone can not search, or it is searched, but the input password is invalid. The charger is damaged (go to the repair shop to replace the charger of the same model to try) In addition, the phone charger and the Bluetooth headset charger cannot be used at the same time. oppo Bluetooth headset can not be charged
How to solve the OPPO true wireless headset does not charge problem