1, lack of battery power battery power depletion is a common reason for wireless charging can not work. It may be due to long-term use of electrical appliances in the car or forgetting to turn off the equipment. If the battery is low, try charging it with a charger or trailer to the repair point. Starter failure The starter is the key to starting the car, and its failure will affect wireless charging. If you suspect a starter problem, be sure to send it to a repair shop for inspectionAnd repair.
2, the wireless charging panel may be damaged, can not normally sense the signal of the phone. First of all, you need to check whether the phone has wireless charging function, if the phone is fine, try to replace the wireless charging panel. The fuse of the wireless charging power supply may have blown, resulting in the normal flow of current. Please check the power fuse, if damaged, need to replace the fuse to ensure the normal operation of the charging system.
3, the possible reasons for the failure of wireless charging of Mercedes-Benz vehicles are as follows: Wireless charging panel is abnormal: When the wireless charging panel is damaged, its function may not work normally, resulting in wireless charging cannot be carried out. Power fuse damage: The wireless charging power fuse is a key component, if it is damaged, it will directly affect the power supply of the wireless charging system, resulting in problems.
4, secondly, the starter failure! - may also be the crux of the failure of wireless charging. If the starter does not work properly, it cannot transmit power to the battery, and wireless charging naturally cannot be started. Also, drive the computer! The health status of the charging system is also critical, and any failure can affect the normal charging process. Finally, the battery pack is loose! - is also a possible reason for wireless charging does not respond.
2, not suitable for mobile phone power charger, will damage the mobile phone battery. Wireless chargingElectrical technology, derived from radio energy transmission technology, low-power wireless charging often uses electromagnetic induction, high-power wireless charging often uses resonance, by the power supply equipment to transmit energy to the power device, the device uses the received energy to charge the battery, and at the same time for its own operation.
3, usually choose a place near the driver's seat. Next, connect to the cigarette lighter and use the USB data cable to connect the wireless charger to the cigarette lighter interface of the car respectively. Make sure that the charging pad is clean and place the phone face-up in the charging area of the charging pad. If the green charging symbol is displayed, the phone is properly placedStart charging.
4, Apple 11 wireless charging can not be used Apple 11 wireless charging can not be used may be the mobile phone protection case is too thick, it is recommended to choose a thin mobile phone protection case when using wireless charging or do not use. The phone case is too thick will affect the induction of the charging coil and the wireless charger in the phone, resulting in normal charging.
5, encounter such a situation must check whether the desktop of the wireless charging station is placed other debris, if other debris is placed, the wireless charging station of the crown road will be drip-sounding alarm, the owner of the usual wireless charging station as far as possible do not have to place objects. As well asThe wireless charging module is faulty. Troubleshooting: VDS can not scan the wireless charging module. According to the circuit diagram of this model, the wireless charging module is powered by the F2/42 fuse of the meter distribution box. Check that the fuse is normal and measure that the fuse has 13V voltage. Remove the wireless charging module located below the front end of the central channel, and measure that the power supply of pin 1 of the connector of the wireless charging module is normal.
3, the car charger uses the car cigarette lighter as a power socket to charge the mobile phone directly. Due to the low voltage provided by the car, only overload protection circuit is required inside the car charger. Vehicle chargingThe front end of the socket is designed with a safety tube, when the current exceeds the overload protection circuit can withstand the range, the fuse will immediately blow, play a protective role. It should be noted that charging can only be done when the vehicle engine is started.
4, wireless charging panel abnormal: when the wireless charging panel is damaged, its function may not work normally, resulting in wireless charging can not be carried out. Power fuse damage: The wireless charging power fuse is a key component, if it is damaged, it will directly affect the power supply of the wireless charging system, resulting in problems. Mobile phone wireless dysfunction: If the mobile phone wirelessThe charging function is damaged, and wireless charging cannot be achieved even if the charging panel and line are normal.
5, wireless charging power supply fuse may have been blown, resulting in the current can not flow normally. Please check the power fuse, if damaged, need to replace the fuse to ensure the normal operation of the charging system. There may be a problem with the wireless charging function of the phone, please try restarting the phone, or connect it to another device to test the charging to determine whether the problem is the phone itself.
6, the car charger uses the car cigarette lighter as a power socket to charge the mobile phone directly. Because the voltage provided by the car is higherLow, so the car charger inside only need to have overload protection circuit. The front end of the car charger socket is designed with a safety tube, and when the current exceeds the acceptable range of the overload protection circuit, the fuse is immediately blown and plays a protective role.