1. The usb port is faulty. The current of the usb interface is too large during charging, exceeding the mouse load. The mouse stops working. The mouse is faulty. Replace the mouse and observe. The laptop mainboard is faulty. Excessive current during charging. The current of the usb port is overloaded. After-sales testing is recommended.
2, the driver of the system is not suitable or the system is unstable will cause similar results. Solution: It is recommended to drive the motherboard firstIf it is still the same, install it with a more stable system version. This situation occurs when charging, voltage instability caused by computer components can not normally transmit instructions, receive instructions, processing instructions caused.
3, this situation has the data cable or charger damage, the mouse switch is not opened, the computer USB interface problem and other reasons. Possibility of damage to the data cable or charge. The mouse switch is not open: Apple mouse has a professional switch, a small switch under the wireless mouse is opened, there will be a constant speed of electricity flashing light, and then connect to the iPad or computer.
4, may be set the power management caused by the connection instability, the solution is as follows. First, in the computer desktop, right-click the computer and click "Manage". Then open the computer management interface, click on the "Device Manager" function. Then in Device Manager, click Universal Serial Bus Controller. So find your mouse USB device, then mouse right click, click [Properties].
5, according to the description, there is a problem with the power adapter or the charge management circuit in the computer, because some kind of failure inside the adapter makes the power supply appear serious high-frequency interferenceAfter the high-end game mouse is damaged, most will find a professional to repair. The repair method after the mouse is damaged, see where it is damaged.
The solution is as follows: Check whether the switch on the mouse is on. If not, turn on the switch button. Make sure the battery in the mouse is alive. If the battery is dead, replace it with a new one. Confirm that the receiver is connected, if it is connected, try to replace another USB port to try. The above checks are no problem, most of the mouse hardware is broken, can only replace a new wireless mouse.
To eliminate the above faults, it is necessary to consider whether the battery hasWhen the battery is out of power, replace it with a new battery. If the light of the mouse with a new battery is still not bright, it is probably the problem of the mouse itself. Note: The mouse light is on does not mean that the mouse battery must have power, wireless mouse normal work requires a certain voltage, if the battery voltage is too low, even if the light is on, but the mouse can not work normally.
The computer wireless mouse does not move, solution: confirm whether the switch on the mouse is open. If not, turn on the switch button. Make sure the battery in the mouse is alive. If the battery is dead, replace it with a new one. Verify that the receiver is connectedIf yes, try to replace another USB port to try. The above checks are no problem, most of the mouse hardware is broken, can only replace a new wireless mouse.
Then you look at the later you can not use it when the computer does not have its connection indication if not, it may be that your Bluetooth frequency needs to be reset. It may be that the frequency band has a problem. Question six: The wireless mouse is broken, is it necessary to repair? A broken mouse can be repaired. Most mice are relatively cheap and therefore rarely repaired, but this does not mean that a broken mouse cannot be repaired.
1, the device is flashing red for the following reasons: Low battery: If the Bluetooth mouse battery is low, it may not be able to use normally because there is not enough power, at this time there will be a flashing red, at this time you need to replace the battery in time. Connecting: When the Bluetooth mouse is connecting to a computer or other device, it will flash a red light, which indicates that the mouse is in the process of connecting and may take a minute or two to successfully connect.
2, Logitech wireless mouse lightSome Logitech mice use battery power, and each battery can be used for a limited time, when the battery is relatively low, the indicator light will be red and constantly flashing. At this time, there is no hurry to change the battery, because the remaining power can be used for a period of time, you can prepare a new battery, and then replace it after the battery is completely exhausted.
3. It may be because there are foreign objects on the mouse pad. Please replace the mouse pad and try again, or check whether there are other foreign objects at the bottom of the mouse. Replace the mouse interface, the mouse interface plug is not in good contact, causing the mouse and plug are not fitYes, causing the red light to blink. The battery is insufficient, which cannot support wireless mouseless operation, or causes the operation department to be flexible, causing the mouse to blink. Replace the battery promptly.
4, for wireless mice, the red light flashing usually indicates that it has entered the energy-saving mode. The wireless mouse automatically goes to sleep to prolong the battery life. When you move the mouse, even if the red light goes on, it may not actually be activated. The solution is simple, just press a button on the mouse, wake up the mouse, let it reconnect to the computer, and the mouse pointer will return to normal work.
5, the mouse can be used.It may be because there is a foreign body on the mouse pad. Please replace the mouse pad and try again, or check the bottom of the mouse for other foreign bodies and remove them in time. When replacing the mouse port, the mouse port plug is in poor contact, resulting in mismatch between the mouse and plug, resulting in a blinking red light. The battery is insufficient, which cannot support wireless mouseless operation, or causes the operation department to be flexible, causing the mouse to blink. Replace the battery promptly.
1. Cause five: Whether it is resolved by remote controlSometimes you may choose to allow the remote control to be controlled when you use the remote solution to the problem, but forget to end the remote control, such as using the remote control in qq, so you can check whether the mouse is moving.
2. The system is faulty. There's other software running in the background. The mouse speed is set too fast. Methods and steps to solve the problem: Method 1: Check whether the computer has a problem. Open "My Computer" and click "Open Control Panel". In the Control Panel, find "Mouse" and click to enter the mouse properties page. On the mouse properties page, select""Hardware" to check the device status.
3, the driving problem of the computer, sometimes the driver is confused or missing, will lead to the mouse is not controlled. You can uninstall the driver directly and then reinstall it. The mouse itself is faulty, you can replace a mouse for testing. If a user's finger touches the touchpad inadvertently while typing, you can disable the touchpad function. When the user uses the mouse, the mouse pad is not used or there is a problem with the mouse pad, the mouse will move by itself.
4, the computer mouse is not controlled, generally because of: the computer itself, the mouse driver problem, the computer virus caused. electricitySome computer motherboard itself has problems, processing the mouse signal circuit has a classic or short circuit phenomenon. This situation will lead to mouse running, and the average user can not solve. Such a problem needs to be sent for after-sales maintenance.
5, the mouse is not controlled always jump, it is likely that the mouse sensitivity is too high, if it is able to adjust the sensitivity of the mouse, then we can adjust on the mouse, if not adjusted, then open the computer, click Settings - control panel, and then in the mouse Settings will appear a window, click hardware, select the mouse and adjust it. <6, if the computer mouse is not controlled by random points, you can try the following methods: check whether the mouse cable is plugged in, or replace the mouse cable. Check that the mouse is clean, and if there is dust or dirt, you can wipe it with detergent or a cotton swab. Check that the mouse driver is working properly and you can try to reinstall or update the driver. Check whether your computer is infected with viruses or malware by running an anti-virus software to scan and clean it up.
1. Whether the USB port isThere is a fault. We can find a good mouse and test whether the USB interface is faulty. ② Whether the mouse is damaged. Check that the mouse optical engine is glowing. If the engine does not emit light (except for non-visible light engines), you can plug the mouse into another computer to see if you can identify it. ③ Whether the mouse is in poor contact. Plug and unplug the mouse repeatedly to see if the computer can recognize it. Or replace the USB port.
2, replace a new battery, because the power is insufficient or no power unlimited mouse can not be used normally. Check that the receiver of the unlimited mouse is fully plugged in.
3. ComputerLack of power supply or failure of USB interface: some keys and mice require a certain voltage to drive normally, and the USB interface or USB dock on the front panel of the desktop computer is prone to lack of power supply, resulting in the situation that the keys and mice cannot be used. You can try connecting the keyboard and mouse to the motherboard USB port on the back of the desktop, or connecting the USB dock to the power supply. Key and mouse drive failure: Some keys and mice need to be driven to work normally.