HandThe phone did not respond to the wireless charger, mainly because the phone did not turn on the wireless charging function. Tap to open the "Settings" option on your phone. On the General Settings page, open the "WPT Charging" feature. After the mobile phone wireless charging function is turned on, the mobile phone is adsorbed on the wireless charger for charging.
Sometimes the iPhone protective case is too thick will also lead to wireless charging, then you can try to remove the iPhone protective case, and then put back on the wireless charging board to charge.
Put the mobile phone wireless charger in a stable position. When you need to charge, turn your phone's display upWith wireless charging, Huawei car wireless charger only supports mobile phones that meet the qi wireless charging standard. The charging distance is too far, and the wireless charging distance is generally less than 5mm. Chargers are not compatible with mobile phones, and some in-car wireless chargers only support certain brands or models of mobile phones.
3, the reason why the situation can not be wireless charging is: the charger power is not enough Huawei car wireless charger power is generally 10W, if your mobile phone supports 15W or higher power wireless charging, then Huawei car wireless charger may not be able to charge your mobile phone. At this point, you can try to use support 10W powerCharge your phone, or replace it.
4, if your Huawei car wireless charger does not work properly in the standby or parked state, there are several reasons: Power supply: The vehicle's cigarette lighter jack usually loses power when the engine is turned off, which may cause the car wireless charger to not get enough power supply. Make sure your vehicle's cigarette lighter jack still provides power when parked.
Check whether the phone is overheating, it is recommended that the heat dissipation barPieces are charged in a better environment. Check whether the wireless charger indicator light is on normally, and check whether the connection between the charging base, data cable, charger, and power supply is in poor contact. It is recommended to reinsert the wireless charger. Verify that the center of the phone is placed in the center of the wireless charging base during charging, and remove other items (such as bus passes, metals, etc.) between the device and the wireless charger.
The methods that can be taken in this case are: make sure that the phone is compatible with the wireless charger, check the charger and the power adapter, and check the alignment between the wireless charger and the phone. Make sure the phone is compatible with the wireless charger: Be sureYour phone supports wireless charging, and the wireless charger is compatible with your phone model. Different phone models may have different charging standards, so you must use a wireless charger that supports your phone model.
Because some mobile phone protective case is too thick, or the material of the mobile phone protective case may affect the recognition function of the mobile phone wireless charger, it is recommended that you remove the mobile phone protective case and try again. 4, please check whether there are other items between the mobile phone and the wireless charger. Wireless charging converts electrical energy into magnetic energy for transmission to the phone, and if the magnetic energy is interfered with, charging will be affected.
Please check the connection of the wireless charger Please check whether the connection between the charger, data cable and wireless charger is normal; Whether there are other items between the mobile phone and the wireless charger, such as mobile phone protective cases, metal foreign bodies, etc.; Whether the mobile phone center is aligned with the center of the wireless charger base; Whether the wireless indicator light is on.
The reasons are as follows: Check whether a wired charging device is also connected. Check the connection of the wireless charger, and whether the connection between the charger, data cable and wireless charger is normal.
Please check whether the wireless reverse charging switch is turned onNext: Set the battery and turn on the wireless reverse charging switch. Please confirm whether the battery of your charging phone is more than 20%. If the battery of the phone is less than 20%, please use the charger to charge the phone first, and then wireless reverse charging after the battery is higher than 20%.
1, the solution to the wireless charger flashing 3 times is not bright: check whether the location of the mobile phone is placed; If the mobile phone with a relatively thick mobile phone case, it is recommended to take off and try; You can change to another wireless charging or support wireless charging mobile phoneTry alternate connections to eliminate the cause of the problem.
2, millet wireless charging green light flash three times, there are the following reasons: because the mobile phone protective shell caused by too thick connection failure. Wireless charger is not the official original charger, resulting in the mobile phone identification device is not successful. The wireless charger is in poor contact, resulting in the failure to perform normal wireless charging operations. The data line of the wireless charger is abnormal, resulting in the wireless charger cannot work normally.
3, when the millet wireless charger, millet wireless charger (universal fast charger) LED light status is green flashing, millet wireless chargerIn the error and protection phase. At this time, you should pay attention to whether there is a metal object placed on the wireless charger, please remove it and charge it again.
4. Check whether the mobile phone is well placed. If the phone has a thick phone case, it is recommended to take it off and try it. If it is convenient, you can change other wireless charging or support wireless charging mobile phones to alternately connect to try to eliminate the cause of the problem.
5, normal, whether it is wire charging or wireless charging, it is bright for a moment when it is just charged, and it is not long. You can put the headset in, then open the headset case and check the battery through your phone.
2, finally, if the above methods are ineffective, you may need to consider replacing the charger or contacting Xiaomi customer service for further support and solutions. To better understand the problem, we can consider a practical example. Suppose a user puts his Xiaomi phone inXiaomi wireless charger on the charge, but found that the green light began to flash.
3, the charger has a problem. If the above two cases are not a problem, then there may be a problem with the charger itself and it needs to be replaced or repaired. If you encounter the situation that the millet wireless charger light has been flashing, you can first try to adjust the distance between the charger and the phone, or check whether the interface is loose. If the problem still exists, it is recommended to contact Xiaomi customer service or go to a professional electronic repair shop for repair.
4, millet 9 wireless charging does not respond to the solution is: if with a protective shell, take off the shell to try. Tap to setSet - my device, the top MIUI version, click in, the top right corner three points, download the latest complete package, re-brush the system to try to eliminate the problems caused by the simple package. After the system is updated, turn on the screen for the first time and unlock it, then wait a few minutes before clicking to run the APP. The first boot may take a long time.