Nanfu wireless charger can charge any mobile phone that supports wireless charging, but it is ordinaryMobile phone does not have wireless charging this function, need to configure an external wireless receiver to use Nanfu wireless charger charging. Science popularization, to achieve wireless charging requires a transmitter and a receiving device, wireless charger is the transmitter, and to install a receiving device (external wireless receiver) on the phone to achieve wireless charging.
First of all, science, not all mobile phones support wireless charging, not just buy a wireless charger can be charged, only support wireless charging mobile phones, the current support for wireless charging mobile phones are iPhone8/8p, iPhoneX, Mi MIX2S, etc. Of course, if your mobile phone does not have wireless charging function, you can buy an external wireless receiver, so you can use Nanfu wireless charger to charge your mobile phone.
Adopts vertical structure, and double coil design, 4mm induction distance, mobile phone with shell can also be charged, you can charge while watching movies; Max bai supports 20W flash charge, fast charging; Support Qi wireless charging standard, compatible with zhi most mainstream charging dao equipment, is a collection of home, office and other functions in one of the universal wireless charging products.
Recommend you this: Banghua wireless charger, vertical horizontal can be charged, very convenient.
Added a self-sensing silent fan. The self-sensing silent fan adopts the cold air circulation convection design, which can heat the wireless charger at the same time, but also heat the mobile phone, increase the heat dissipation efficiency, so that you don't have to worry about the problem of charging and heating the mobile phone.
1, obviously there is a problem with this socket, it should be the socket contact shrapnel is not good, or poor contact caused, it is recommended to replace the patch board.
2, it may be that the electrode in the insert board is too loose or the gap is too large. Resulting in no contact.
3, It is recommended to use the standard charger to charge it is recommended that you use the standard charger and charging cable of the tablet to charge. Non-standard chargers and data cables may not be compatible with the tablet, resulting in the tablet not being able to charge. 2, please check whether the charging interface is abnormal Check whether the flat charging interface is blocked by foreign matter, mold, corrosion, internal connection cable damage, etcIf there is such a phenomenon, it is recommended that you go to the nearby customer service center for cleaning and testing.
4, this is the virtual connection inside the socket, that is, in the state of partial contact, when there is no load, once the load increases, the virtual connection part will be disconnected, there is no electricity, low power consumption of mobile phone charger, intermittent charging state, more proof that the socket is damaged, replace the new socket can be, the specific steps are as follows: Turn off the electricity in the room. Power off. Use a screwdriver to pry off the socket cover.
5, the copper gap in the first socket is not good with the charger plug. Take apartJust put it back on after the molding.
6, otherwise it may lead to short circuit of the charging port. If your charger is the first time to charge the tablet, then you have to look at the voltage of the charger and the charging voltage of the tablet, if the charger voltage is lower than the charging voltage of the tablet, then the electricity is not charged. This requires you to change a charger that is suitable for the tablet to use, because this is a problem that the charger does not match the tablet, rather than a fault.
1, the voltage is not the same as the previous battery, the new battery also has no electricity, the factory battery is not 100% good.
2, if the mouse can not be used with a new battery, check the wireless switch of the computer is not a problem, if there is no problem, then search the wireless device, see if the mouse will be able to search. In the inspection, look at the spring and metal card inside the mouse that hold the battery. They are welded to the circuit board, and check for signs of looseningGenerally, the working voltage of the wireless mouse is low, and it is the use of battery power, which will not have too serious problems.
3, you may buy Nanfu battery is false Rome inside there is no electricity, you change other batteries to try.
4, I just last week also encountered a similar situation, situation description: the indicator light is not bright, but the function of the mouse can be normal, specially found a friend in the original factory to consult, the answer is: It is best to find a dealer to exchange or return processing, so that it is not bright but does not affect the function, the possible reason is that one or some of the original pieces of the circuit board is broken, and it may be that the solder paste is not attached.
5, it is recommended to buy another brand battery to try, Nanfu battery also has a fake, if there is a problem with other batteries, that is the problem of the mouse, the battery contact piece is no problem, look at the switch contact piece.
6, the battery and then change to other appliances to try, if there is no power, it is the quality of the battery. If there is electricity, you can confirm whether the previous contact with the mouse is poor.