Perform the following steps to enable the magnetic function of the Apple 12: Connect the mobile phone to the adapter to ensure that the device is successfully identified. Open the "Settings" menu and enter the "General" option. Find the "Charging Interface" or "Wireless charging" function in "General". Open"Magnetic charging function "option, you can use magnetic charging mode.
** Get a MagSafe charger ** : First, make sure you have a MagSafe charger for the iPhone 14, which has a magnetic adsorption design and fits tightly into the iPhone 14. ** Connect the charger to a power supply ** : Connect the MagSafe charger to a power outlet or USB port on your computer using an appropriate charging head and cable. Make sure the charger is properly powered on.
Get an Apple wireless charging device. Wireless charging kitAfter connecting the power supply and placing the phone on it, the magnetic charging operation of the Apple 13 can be realized. Magnetic charging is a charging technology that uses the principle of magnetic attraction to automatically adsorb and connect the charger with the device through magnetic force to realize charging without inserting or removing the charging cable.
Pull the magnetic charging bank to the back of the phone, and the charging animation will appear on the main screen of the phone and display the battery ring. Magnetic charging cable is also known as magnetic charging cable, magnetic charging cable, magnetic charging cable, magnetic charging cable, magnetic data cable, etc. Mainly used in smart wear, 3C digital, smart home, car navigation detection, medical equipment and other electronic productsRealize charging, signal and other aspects of transmission.
Turn on the magnetic charging of the Apple 13 Using the magnetic charging of the Apple 13 is very simple, just plug in the charger when out of the box, and make sure that the charger's power cord is connected. Next, you only need to place the back of the Apple 13 near the appropriate part of the charger to feel the effect of magnetic charging. At the same time, the Apple 13 shows the current charging status on the back, including the percentage of power and remaining time.
Perform the following steps to use Apple Magnetic charging: Prepare tools. You need an iPhone that supports MagSafe charging (e.gMagnetic field, so it will not affect the wireless charging process. 2, the car details storage space is rich, the front and back cup holders are complete, the hollow shape below the central channel can put a lot of debris, and it also adds two USB interfaces and a 12V interface. There are also more places to put mobile phones in the car, and the storage slot under the front cup holder also has a wireless charging function to facilitate mobile phone charging. The opening of the trunk is relatively small, and the interior space is basically the size of a minicar.
3, iMask electric toothbrush iMask is a veritable high-end electric toothbrush leading brand, but also electricityThe top brand in the quality, performance and experience of the toothbrush industry.
1. On the back of the machine, right in the middle. The irregular round part in the middle of the picture is the part that charges (or discharges) wirelessly.
2, after the wireless charger is powered, directly place the phone screen facing up in the center of the charger or the position suggested by the manufacturer to charge.
3. How to set Huawei p40pro wireless charging?Connect the charging head to the charging base using a data cable, and then plug the charging head into the power supply. Place the charging base on the table, with the phone's screen facing up in the center of the charging base. After the phone is placed on the charging base for a few seconds, there is a "drip" sound, indicating the start of charging. I tip: The wireless charger is composed of a charging head, a data cable and a charging base.
Magnetic absorption of the magnetic shell. The middle of the mobile phone case is embedded with a small ring holding wireless charging magnetic ring, which can improve the wireless charging effect of the mobile phone, and the magnetic force is as high as 10N, which perfectly matches the wireless charging ring of the charging device.
1, wireless router Ann can signal can be enhanced. Step 1: Take a used beer can and wash it. Step 2: Pull outPull the loop. Step 3: Make a circular cut along the bottom of the can to remove the entire bottom. Step 4: Cut around the top of the tank (be careful not to cut all of it, leaving a part of it uncut, and this part must be close to the mouth of the tank). Step 5: Draw a vertical line on the opposite side of the remaining part and cut the iron sheet along the line.
2, has a certain enhancement effect, the principle is to concentrate the signal of the omnidirectional antenna to a certain Angle for transmission. The first step is to clean the can and pull out the pull ring. The second step is to cut the tank near the bottom and then remove the entire bottom. Third, cut a section of the tank near the top, at the mouth of the tankLeave a 1 to 2 cm section uncut. The fourth step, the head and tail have been cut the tank part lengthwise half cut.
3, placing cans on a wireless router does not enhance the signal output strength of the router itself. This practice is actually to convert the omnidirectional antenna of the router into a directional antenna, thereby improving the receiving strength of the wireless signal to a certain extent.
4, hello, you can, this is because the surface of the can reflects electromagnetic waves, so that the signal is more concentrated, the wireless router antenna is emitted 360 degrees spherical wave, after the can is set on the can, the can can electricityThe magnetic wave is concentrated 180 degrees, so the can plays a role in making the electromagnetic wave more concentrated.
1, the steps are as follows: first, cut the end of the USB data cable connected to the phone with scissors or a knife, and then cut a short section of the long end of the data cable into the incision, at this time you will see four green, red, white and black lines, cut the green and black two, and cut a small amount of the red and green twoSection insulation exposed copper wire.
2, open the back cover of the smartphone, and then take out the wireless charging receiver ready; Or the protective layer of double-sided tape peel; The next task is to connect the receiver's metal shock to the smartphone battery, which is the most difficult part of the process. However, as long as you are careful to ensure that each metal shock is connected together, it can be done.
3, is the use of the principle of electromagnetic induction, if you can do electronic then you can do a vibration circuit, the vibration signal added to a coil, another coil string a LED, the twoThe light goes on when the coil is close. If you want to produce your own, you can go to Xincotec, there are very cheap modules. You can also buy IC processing. It's cheap to make.
4, the working principle of electromagnetic induction, we have learned in junior and middle school physics. There are two coils in the phone, and when the charging pad is plugged in, it creates a magnetic field. The coils in the phone, in turn, generate an alternating current. Then convert alternating current to direct current, and we can charge our mobile phones. Although the charging principle is very simple, the production process is really very complicated, and it is not as simple as we can imagine at presentSingle.