1. The airport should be plugged into the USB port. Identification requirements:When used at the airport, it generally involves the need to charge electronic devices or data transmission. To achieve these goals, USB interfaces are often used. Therefore, airport should refer to a device with wireless connectivity, and its charging and data transmission depends on the USB interface.
2. First, plug the AirPort Express into a power outlet and connect your ADSL or cable modem. Then, open the pre-installed AirPort software, which is located in your Mac's list of programs. The software will guide you in a user-friendly way,Step by step, including asking for the necessary information, setting up encryption protection, and configuring the computer to connect to the newly set network.
3, airport is the first charging box. If your AirPods are dead, you just need to put them in the charging case to charge them. In addition, it should be noted that the charger also needs to be charged, you can use the Lighting cable attached to AirPods to plug into the interface of the charging case, and connect the charger or USB to the other end. After a full charge, the AirPods can provide up to five hours of listening time or two hours of talk time.
chip is different: the airpods generation uses the W1 chip, while the second generation uses the H1 chip. Different phone connection speeds: The airpods 2 has better connection speeds than the airpods 1Fast, and the time delay is shorter than one generation. The appearance is different: the wireless charging case of airpods 2 has more one-person indicator than that of the first generation, and the earphone body of the second generation airpods has more than that of the first generation.
The appearance is different. Although there are differences in appearance, it is difficult to distinguish between the first and second generation, because the charging case of the wired version of AirPods 2 is exactly the same as that of the first generation, but the wireless version of AirPods 2 has been significantly changed. For example, the back button of AirPods 2 wireless version is moved up, and the hinge is changed from the original bright surface to a frosted process.
The difference between airpod1 and 2 is that the battery indicator of AirPods2 wireless charging case version is changed from the interior of airpod1 to the front of the headphone case. The AirPods2 adaptation button moves up. AirPods2 battery case rear chain by 1 generation tossLight replacement into a matte process. The AirPods2 headphone body is printed with three lines of characters, while the first generation of AirPods only have the first two lines.
Find the reset interface: First, find the reset interface on the back of the router. Reset: Use a pen or other small tool to gently press the reset button to restore the router to factory Settings. Download andInstall the AirPort utility: This utility is setup software specifically designed for APPLE wireless routers. Set wireless parameters: Run the AirPort utility and follow the interface instructions to set wireless network parameters.
First find the interface and see if you have inserted it incorrectly. Take a pen and stab the "dot" in the back to restore factory Settings.
Repeat the first step to open the "Airport Management utility" Click the wireless network on the left, click "Configuration", enter the wireless router password you just set, OK. Here is the "upgrade" button.For Internet users, please upgrade firmware 1, Airport TAB. One thing to note here is that interference may occur if your wireless router uses the same channel as other wireless routers around it.
The easiest way is to use the setup wizard, step by step to select the Internet access method, user name, password, wireless SSID, wireless encryption method and key, mac address filtering, and so on. This is easy. Just follow it step by step. Then open the modem, the route will automatically connect to adsl, no longer need to use the computer to dial up, which will achieve a lot of peopleSaid it was on the Internet. Now that the setup is complete, move on to the next question.
1, eliminate compatibility problems, change the terminal device: put this AE (Airport Express or Airport Extreme) in front of other Mac or iPhone/iPad, connect the wireless, use the "Airport utility" to search againCheck it out (iOS 5 has an Airport utility). If you can find it, it is recommended to upgrade this AE to the latest Flash Rom (current version 2) and then bring it back to connect to the original computer.
2, in addition, use the network cable to connect the airport and Pc, the same search airport - my problem is solved, restart the computer should be able to solve, if not, RESET it, it is very simple, and then all the passwords will automatically be public. If there is a problem with the Pc wireless card, click on my computerRight-click Management-Service and restart the wireless zero configration service.
3. If the green light is not on, the AirPort utility cannot find the wireless device. In the power state, press the reset button for about 10 seconds, and then turn off the power, wait for about 5 minutes (complete discharge), and restart; When the device is connected to the power supply, press and hold the reset button for a few seconds with the tip of the pen to restore factory Settings.
4, the newly activated AirPort for the first time access, just in the iOS device "Settings" "wireless local areaNetwork ", select "Set AirPort" for network name and password input, you can start the basic operation. Further base station management requires the use of Apple's official AirPort Utility App, which can be downloaded for free from the iTunes App Store.
5. In the Base Station Picker of the AirPort utility, select the primary base station and click Continue. If prompted to reset, select "Cancel" and continue. Go to the "Manual Settings" option and enter the base station password if necessary. Next, click AirPort in the toolbar,Then select the "Wireless" option. In the "Wireless Mode" menu, select "Create Wireless Network" and select "Allow this network to be extended".
6. Open the AirPort utility (On a Mac, select Go To Applications from your desktop, click the Utilities folder, and then open the AirPort utility. In Microsoft Windows, select Start, All Programs, AirPort to open the AirPort utility). In the Base Station Picker,Select Extend Wi-Fi base Station, then click Continue.
1, the function of the button on the airport charging case is the pairing button, that is, airpods and mobile phones are paired, especially with non-Apple devices. If the airpods have been connected to the iPhone, you can reset the airpods by holding down the button on the back of the airpods charging case, and then you can reconnect the AirPods.
2. Connect the phone. To determine how much power is left in the charging case, all you need to do is move the phone near the charging case, then open the cover, and an animation will pop up on the phone's screen. At this point, it will show exactly how much power the airpods headphones and charging case have, for example, 100% remaining. You can also use this method to find out the charge level of the charging box at normal times. Look at the indicators. Everyone knows that Airpods have an indicator light on their charging case.
3, airportpro use method is as follows: open the AirPodsPro charging case, and then close to the Apple phone, seeThe iPhone appears an animation prompt and then connects. Wait for the phone to connect to the headset, put on the AirPodsPro headset, and then you can play the phone audio through the headset. In the ear lobe of the AirPodsPro there is a concave design, pinch with your finger to play/pause, press twice for the next song, and three times for the previous song.